Okay, so you love your man, or maybe just your manhood. Either way, you cannot lose if you make your own replica of your favourite phallic friend.
At first glance I am sure that you think “hey, that’s cool…but wait…lots of components means lots of work”. That is both; true and not true. Yes, you are going to need the dedication to follow through the project with great accuracy but the rewarding part is that it will be simple if you choose to do so.
The kit includes: *molding powder, *thermometer, *wide Popsicle stick (to stir and scrape), *plastic tube to mold with, *rubber mix (2 parts), *instructions, *glow powder (if Glow kit), and the vibrator.
So, a summary of the process is as follows…
Set everything up! Be that little over-achiever that you have buried inside…prep the bowl, the cardboard, the spoons, etc.
You’re going to need to hit the right degree for your water to mix properly with the molding powder. *Important* What I found was easiest, get your big bowl, measure out the water and have it a little hotter than you really need it. Set the thermometer in the bottom of the bowl so you can watch your temp. drop to perfection. Before it hits perfection you can start to get “him” hard and figure out how long you will need the tube to be. Press the FLAT, Closed end close to his body and mark a little bit further than the penis tip. You can then take a sharp knife and saw on your sharpie line to cut the tube shorter. If your penis is curved, you can mark the curve and cut there, duct tape the rest of the tube back on, but in a curved manner and then measure and cut from there.
Cut the mold powder packet ahead of time to save time in the mixing process. Have a timer set for 2 minutes, make sure he’s hard; make sure your water is at the proper degree. (If not, don’t stress, just re-measure the water at the correct degree because you need this to be correct.) Start the timer for 2 minutes, drop the powder into your bowl of water and mix very quickly and as effectively as you can for one minute, hurry up and pour mix into tube (don’t fill too much), with the last 30 seconds on the timer, he should be inserting his penis. If he touches the sides, turn, or if it’s been in there for a few seconds already, just leave it lol. If he moves, you could kill your mold. Give the mold 3-5 minutes to perfectly form, pull penis out carefully. Let the mold set for around 2-3 hours, and then you can start the rubber mixture.
Follow the directions on the rubber mixture (add glow if applies); have your vibrator rigged into a piece of cardboard or something so that it won’t get buried in the rubber mix. Pour the rubber into the mold, don’t fill, put vibrator in, see if you need more rubber, if so, move vibe over and pour more. You can use tape to help position the vibrator or just leave it as it is. Have the mold sit for 24 hours before you pull the clone out, and you’re all set! If you have any edges to clean up, I suggest using a wood-burning kit with an exacto-blade attachment. Works amazingly! =) The glowing kit really glows amazingly too, by the way! It loads the light really quickly and it glows very brightly.
Possible Mistakes:
* You have the mold mixed, you don’t communicate too well and you both do that “ok GO” thing and no one is ready, both are freaked out. He finally inserts his penis into the mold that has already begun to set and then you end up with a cottage-cheese-looking CHODE clone. Looks like this:
* You trail off from the directions and try to do your own thing. Such as; Oh hey, they suggest to use a penis pump…tube looks like the molding tube, wonder if this cool rubber piece fits on the clone tube?…Put the rubber cap on to make it comfortable to use. Insert penis and find that the molding goop needs to escape but the cool cap you put on makes the excess trap into the tube. Not cool, and you get a funky, shorter penis out of it. Looks like this:
Great Solutions:
* Follow the DIRECTIONS lol. BE Ready. Be very ready.
* Buy some extra molding powder when you purchase your kit, just in case you have one of those retardo moments and you kill your clone. You don’t have to continue and mold your reject Chode if this happens. Just save the rest of your kit and order the powder to finish. =)
This kit was a lot of fun. I love to craft, I love creating. I love my husband’s penis. It would be shallow of me to say that his sex was the 1st sex that I’ve ever enjoyed and that it had a big influence in my relationship with him. So I’m shallow! But I still love everything else about him, too. Maybe I’m one of those “the way to my heart is through my pants” kinda girls. Sorry…lol. No, but really, you will have a lot of fun with this kit and I suggest to do it more than once, Empire Labs has quite a few of different products to clone with. I had to get a little crazy and crafty with my latest kit.
